BASIC RESIN 500g

US$23.45*

Content: 500 (US$46.90* / 1000 Gramm)
Size
Product number: 33010005
Product information "BASIC RESIN 500g"

RESIN BASIC is not really that basic. Developed and manufactured in Austria the material shows excellent properties. It is easy to print and delivers pixel perfect results. Even the smallest details show up with a smooth surface finish.

Application

for Printing with a DLP or LCD 3D Printer

Follow the guidelines of the 3D printer manufacturer to set up the 3D print. The necessary exposure varies for every printer model. Recommended setup: Normal Layers 0,025-0,15mm 10-15 sec. expsoure (RGB) 2,5-5 sec. (Monochrom) per Layer , 3-5 Bottom Layers (about 40-60 sec.) per layer
Postprocessing

  1. Drain the model over the resin tank
  2. Remove the model from the platform
  3. Wash off the left over resin from the model with ISOPROPANOL, TPM or RESIN CLEANER
  4. Remove the support structure
  5. Post-cure the model for mix. 10 minutes under UV light

Hazard and Precautionary Statements

  • Signal word Warning
Hazard statements
  • H317 - May cause an allergic skin reaction.
  • H413 - May cause long lasting harmful effects to aquatic life.
Precautionary statements
  • P101 - If medical advice is needed, have product container or label at hand.
  • P102 - Keep out of reach of children.
  • P273 - Avoid release to the environment.
  • P280 - Wear protective gloves/protective clothing/eye protection/face protection.
  • P302+P352 - IF ON SKIN: Wash with plenty of water.
  • P333+P313 - If skin irritation or rash occurs: Get medical advice/attention.
  • P501 - Dispose of contents/container in accordance with local/regional/national/international regulations.

Download the Material Safety Data Sheet

Technical Data

  • Density: 1,18g/cm3 (20°C)
  • Tensile Et: 3730MPa
  • Tensile strength at yield sM: 74,4MPa
  • Chemical Type RESIN

Download the Technical Data Sheet

Disposal of BASIC RESIN

BASIC RESIN must be disposed of as special waste (paints and varnishes) at the local waste collection point.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.


Suitable accessories

Single Use Nitrile Gloves 100 pcs Size L
Packaging Units: 1 | Size: L
Disposable nitrile gloves are free of allergy-causing proteins and are therefore a skin-friendly alternative to latex gloves. Nitrile gloves are resistant to many chemicals and oils, are tear-resistant, convince with their high elasticity and convey a good sense of touch. They are ideal for use in medicine, nursing and home care. Nitrile gloves are food safe, which makes them the first choice in the food industry & food processing. Test parameters Test criteria Test level AQL Dimensions S-2 4.0 Physical properties S-2 4.0 1000ml water tightness test G-1 1.5 Visual inspection for minor defects G-1 4.0 Technical data Material: nitrile Color: Black Length 240mm, width: 105 +/- 5mm Standards: food safe, CE, EN 374, EN 455, T. 1-4 Disposal of disposable gloves Depending on the product used, gloves must be disposed of accordingly.

US$16.00*
Buy with Apple Pay
TPM Wash Solvent 5L
TPM Wash Solvent (Tripropylenglykolmonomethylether) is a non-flammable, low odour solvent that can be used to clean and dissolve uncured resin on stereolithography (SLA) 3D printed parts. TPM has a lower evaporation rate than IPA and washes about three times as many parts as IPA before needing to be replaced. *TPM is not currently certified for use with Formlabs biocompatible resins. TPM is compatible with the Formlabs Finish Kit, Form Wash, and Form Cure. For a detailed workflow, visit support.formlabs.com. Application Always wear gloves when handling TPM For removing uncured Resin from SLA or DLP printed parts fill your cleaning vessel with the amount specified by the manufacturer. To minimize waste, it´s suggested to pre-clean the parts before placing them in the cleaning vessel to expand the lifespan of your fresh TPM. This can be done in a separate container with either "dirty" TPM from previous cleaning cycles or low evaporation cleaners such as DPM, TPM or PGDA. Place the finished print in the cleaning vessel and clean the parts for at least 5 min. or according to the material manufacturers guidelines. After the cleaning cycle, wash the DPM coated part with water, let the model dry and check for a tacky surface, repeat if necessary, till the surface is not tacky anymore. If it´s still tacky replace the TPM. This product is not labeled as dangerous according to Regulation (EC) No. 1272/2008. General precautions Keep out of reach of children. Avoid breathing dust/fume/gas/mist/vapours/spray. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Store in a well-ventilated place. Keep container tightly closed. Dispose of contents/container in accordance with local/regional/national/international regulations. Technical Data Chemical colour clear Odour typical solvent CAS Number 25498-49-1 Chemical Type Solvent Density 0.96 g/cm3 (20°C) Disposal of TPM TPM and container as well as rinsing water need to be disposed of at an appropriate waste treatment site.

Content: 5 Liter (US$17.85* / 1 Liter)

US$89.27*
Buy with Apple Pay
COLOR AMPULE - Red 1 - 25g
Color: Red 1 | Content: 25g for 1kg Resin
Description COLOR AMPULE is a dye for BASIC RESIN to color it in a wide variety of colors. COLOR AMPULE is availabe in 12,5g for 500g of Resin and 25g for 1kg Resin. The system is designed to only mix one COLOR AMPULE into one appropriate Resin. If more than 12.5g Dye for 500g Resin or more than 25g Dye for 1kg is mixed into the results of the print might deteriorate. Application for coloring Resin Shake the COLOR AMPULE well for 15 seconds Pour the whole content into the Resin securly close the resin bottle and shake for 20-30 seconds Let the resin rest to reove airbubbles that build up during the shaking Hazard and Precautionary Statements Signal word Warning Hazard statements H317 May cause an alergic reaction. Precautionary statements P280 Wear protective gloves/eye protection. P302 + P352 IF ON SKIN: Wash with plenty of soap and water. P501 Dispose of contents/container in accordance with national regulations. Download the Material Safety Data Sheet Disposal of COLOR AMPULE COLOR AMPULE must be disposed of as special waste (paints and varnishes) at the local waste collection point.

Variants from US$3.67*
US$5.56*
Buy with Apple Pay
COLOR AMPULE - Orange 1 - 25g
Color: Orange 1 | Content: 25g for 1kg Resin
Description COLOR AMPULE is a dye for BASIC RESIN to color it in a wide variety of colors. COLOR AMPULE is availabe in 12,5g for 500g of Resin and 25g for 1kg Resin. The system is designed to only mix one COLOR AMPULE into one appropriate Resin. If more than 12.5g Dye for 500g Resin or more than 25g Dye for 1kg is mixed into the results of the print might deteriorate. Application for coloring Resin Shake the COLOR AMPULE well for 15 seconds Pour the whole content into the Resin securly close the resin bottle and shake for 20-30 seconds Let the resin rest to reove airbubbles that build up during the shaking Hazard and Precautionary Statements Signal word Warning Hazard statements H317 May cause an alergic reaction. Precautionary statements P280 Wear protective gloves/eye protection. P302 + P352 IF ON SKIN: Wash with plenty of soap and water. P501 Dispose of contents/container in accordance with national regulations. Download the Material Safety Data Sheet Disposal of COLOR AMPULE COLOR AMPULE must be disposed of as special waste (paints and varnishes) at the local waste collection point.

Variants from US$3.67*
US$5.56*
Buy with Apple Pay