Filter
TPM Wash Solvent 5L
Content: 5L
TPM Wash Solvent (Tripropylenglykolmonomethylether) is a non-flammable, low odour solvent that can be used to clean and dissolve uncured resin on stereolithography (SLA) 3D printed parts. TPM has a lower evaporation rate than IPA and washes about three times as many parts as IPA before needing to be replaced. NOTICE: TPM is not currently certified for use with Formlabs biocompatible resins. TPM is compatible with the Formlabs Finish Kit, Form Wash, and Form Cure. For a detailed workflow, visit support.formlabs.com (external). Application Always wear gloves when handling TPM. For removing uncured Resin from SLA or DLP printed parts fill your cleaning vessel with the amount specified by the manufacturer. To minimize waste, it´s suggested to pre-clean the parts before placing them in the cleaning vessel to expand the lifespan of your fresh TPM. This can be done in a separate container with either "dirty" TPM from previous cleaning cycles or low evaporation cleaners such as DPM, TPM or PGDA. Place the finished print in the cleaning vessel and clean the parts for at least 5 min. or according to the material manufacturers guidelines. After the cleaning cycle, wash the DPM coated part with water, let the model dry and check for a tacky surface, repeat if necessary, till the surface is not tacky anymore. If it´s still tacky replace the TPM. Advantages of TPM Wash Solvent TPM is able to disolve up to 4 times as much resin as IPA The evaportaion rate of TPM is much slower making it easy to store without loosing much of the product Almost Oderless to a slight chemical smell makes working with TPM easier on the people in contact Not Labeled as a dangerous good with no special requirements regarding storage, ventilation or flame hazard makes TPM Wash solvent the perfect indoor, office, Laboratory Solvent Compatability Compatible Formlabs Wash Formlabs Wash L Not Compatible Formlabs Biocompatible Resin - Use IPA Disposal of TPM Wash Solvent TPM and container as well as rinsing water need to be disposed of at an appropriate waste treatment site. Labeling according to Regulation (EG) Nr. 1272/2008 (CLP) This product is not labeled as dangerous. General precautions Keep out of reach of children. Avoid breathing dust/fume/gas/mist/vapours/spray. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Store in a well-ventilated place. Keep container tightly closed. Dispose of contents/container in accordance with local regulations. Download Safety Data Sheets Technical Data Purity   >99% Chemical Name   Tripropylene glycol monomethyl ether CAS Number   25498-49-1 Gravity   0.96g/cm³ (25°C) Download Technical Datasheet

Content: 5 Liter (€15.80* / 1 Liter)

€79.00*
Buy with Apple Pay
PGDA Wash Solvent 5L
Content: 5L
PGDA Wash Solvent (Propane-1,2-diyl diacetate) is a non-flammable, low-odor solvent used for cleaning and dissolving uncured resin on Stereolithography (SLA) 3D printed parts. PGDA Wash Solvent is compatible with Formlabs Finish Kit, Form Wash, and Form Cure. Application Always wear gloves when handling PGDA To remove uncured resin from SLA or DLP printed parts, fill your cleaning pot with the amount specified by the manufacturer. To minimize waste, it is recommended to pre-clean the parts before placing them in the cleaning tank to extend the life of your fresh PGDA. This can be done in a separate container with "dirty" PGDA from previous cleaning cycles. Place the finished print in the cleaning vessel, clean the parts for at least 2 minutes or according to the guidelines of the material manufacturer. After the cleaning cycle, let the model dry and check for sticky surface, repeat if necessary until the surface is no longer sticky. If it's still sticky, replace the PGDA. Labeling according to Regulation (EC) No. 1272/2008 (CLP) This product is not labeled as hazardous. General Precautions Keep out of reach of CHILDREN. Avoid breathing vapors. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy. Keep rinsing. •Store in a well-ventilated place. Keep container tightly closed. An einem gut belüfteten Ort lagern. Behälter fest verschlossen halten. Dispose of contents/container in accordance with local regulations. Download safety data sheet Technical specifications Purity: ≥ 99% Chemical Name: Propane-1,2-diyl diacetate CAS-Number: 623-84-7 Density: 1,06 g/cm3 (25 °C) Download technical data sheet Disposal of PGDA PGDA and containers and rinse water must be disposed of at an appropriate waste treatment facility.

Content: 5 Liter (€18.40* / 1 Liter)

€92.00*
Buy with Apple Pay
n-Butyl Acetate 5L
Content: 5L
n-Butyl Acetate is a clear, colorless solvent with a fruity smell that is suitable for the used for cleaning and dissolving uncured resin on Stereolithography (SLA) 3D printed parts. n-Butyl Acetate is compatible with Formlabs Finish Kit, Form Wash, and Form Cure. Application Always wear gloves when handling n-Butyl Acetate To remove uncured resin from SLA or DLP printed parts, fill your cleaning pot with the amount specified by the manufacturer. To minimize waste, it is recommended to pre-clean the parts before placing them in the cleaning tank to extend the life of your fresh n-Butyl Acetate. This can be done in a separate container with "dirty" n-Butyl Acetate from previous cleaning cycles. Place the finished print in the cleaning vessel, clean the parts for at least 5 minutes or according to the guidelines of the material manufacturer. After the cleaning cycle, let the model dry and check for sticky surface, repeat if necessary until the surface is no longer sticky. If it's still sticky, replace the n-Butyl Acetate. Labeling according to Regulation (EC) No. 1272/2008 (CLP) UN Nummer: 1123 Signal word: Warning Hazard statements H226 - Flammable liquid and vapour. H336 - May cause drowsiness or dizziness. Precautionary statements P101 - If medical advice is needed, have product container or label at hand. P102 - Keep out of reach of children. P103 - Read carefully and follow all instructions. P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P271 - Use only outdoors or in a well-ventilated area. P370+P378 - In case of fire: Use sand, carbon dioxide or powder extinguisher to extinguish. P403+P233 - Store in a well-ventilated place. Keep container tightly closed. P501 - Dispose of contents/container in accordance with local/regional/national/international regulations. Supplemental Hazard statements EUH066 - Repeated exposure may cause skin dryness or cracking. Download safety data sheet Technical specifications Purity: > 99% Chemical Name: n-Butyl Acetate CAS-Number: 123-86-4 Density: 0,88 g/cm3 (20 °C) Download technical data sheet Disposal of n-Butyl Acetate n-Butyl Acetate and containers and rinse water must be disposed of at an appropriate waste treatment facility.

Content: 5 Liter (€13.00* / 1 Liter)

€65.00*
Buy with Apple Pay